Zap / Tongue test

Soapmaking Forum

Help Support Soapmaking Forum:

This site may earn a commission from merchant affiliate links, including eBay, Amazon, and others.

perfectsoap

Well-Known Member
Joined
Dec 12, 2007
Messages
191
Reaction score
1
Ok I have a question. I looked at other post and found conflicting information, so...
I made some soap last night and it is hard or solid now. I took it out of the mold, but have yet to cut.
I touched the tip of my tongue to it and felt a slight zap about one second after I did it. So does that mean heavy Lye or do I need to wait longer to test it??
Yes I have lost my PH paper...
Thank you,
Jeff
 
Jeff, give it a week to cure out, then tongue test it again. :wink: If it still zaps, :shock: it is lye heavy and needs to be re-batched and more oils added. :)

ETA; If you do find your papers, anything 9 and under is safe, 7 to 8 being the prefered range of soap.

Paul :wink:
 
I lick my soap :shock: , doesnt taste good...but it does the job :lol: :lol:

paul- I have an electric PH meter...it has a glass diode (i think that what its called), these are usually used for testing water but do you think theres a way i could use it to test my soap?? it would be quite a bit more accurate than the paper (which i dont have at this time)

EDIT: also in case I cant use that meter, what is the best way to test the soaps PH with strips?? wet a small portion and stick it on or put it in a small bowl, with a few drops of water and swash it around?? I dont want the water to influence my reading
 
Hey Ralphie hows that soap taste?

this is not the way to test for PH.

ralphie_soap.jpg


If you get this effect you may have used too much lye:
face_melt.jpg
 
i generally use pH strips but from what I understand they are generally about 2 units lower than the "true" pH....for example my soaps are generally a 7 so they are really a 9.

I would wait it out a couple of weeks and test it again. It will likely mellow out as it cures.

Hope you don't have to rebatch

joanne
 
A local pool company is running a special spring sale on digital pH meters for $29.00. I'm going to get one from there as it is a pretty decent quality unit. I have tested my soap several times in the past with a less expensive pocket unit and get readings after 6 week cure of 7.6 to 8 on it, depending on the SF discount. Not too shabby.
 
:lol: :lol: :lol: Man that was me as a kid..I remember this clear bar of raspberry soap (really not as good as it sounds) but my mom used it to put in my mouth when i talked back etc... yepp....i got that only a few times.. the taste was enough to motivate me not to!


paul--how did you use the pocket meter to test it?? what was the procedure you followed??
 
I took the bar and sudzed it up really well then touched the tips to the tiny bubbles and took a reading. I read somewhere this was the correct procedure with test strips or with a digital meter. I'll try to find out where I read that tutorial.... :oops:

My mom used a big bar of Lava with ground pumice to wash my tongue with when I messed up. :x Man was that stuff bad tasting. :x :roll:

Paul
 
I think that I kinda gave up on digital pH meter. My numbers started bouncing around when trying to test something, so I don't trust it anymore.
 
Ill probably wind up getting some test strips and then doing both..compare readings and see which one I think is more accurate (if the PH starts bouncing around on my meter then I prob wont use it...or it could mean that the PH is different in different places in the bar...which means the lye may not be totally sap'd)
 
I think my problem was that I didn't maintain my meter correctly. I guess it needs to be cleaned and stored in special solutions.
 
I use pH meters at work. You really need to calibrate them with 4, 7, and 10 pH buffer solutions prior to taking measurements. There is a drift on the scale that seems to occur when the meter is off.

Hope this helps!

joanne
 

Latest posts

Back
Top